Unable to remove nut on lawn mower blade

  • 2
  • Question
  • Updated 3 months ago
  • Answered
I purchased the Ego 21" lawn mower 3 months ago. I am trying to take off the blade to sharpen it but am unable to loosen the nut. I am using a 14mm socket as recommended but it is not budging. I have also tried putting oil/lubrication to no avail. Any recommendations?
Photo of NYWest

NYWest

  • 110 Points 100 badge 2x thumb

Posted 4 months ago

  • 2
Photo of Oregon Mike

Oregon Mike, Champion

  • 37,372 Points 20k badge 2x thumb
The bolt (not a nut) is torqued to around 40 ft lbs so you need a lot of oomph to loosen the bolt. Torque wrench is ideal but a standard wrench with a long pipe of other way to add leverage can get the job done. Make sure you are securing the blade from moving by putting a screwdriver or other ridgid thing into the opening in the bottom of the mower intended for that.
Photo of szwoopp

szwoopp, Champion

  • 69,224 Points 50k badge 2x thumb
Avoid the oil and get a bigger wrench - you just need leverage working in your favor (and in a counter clockwise direction).  A nice pair of leather gloves works much better than a screw driver to hold the blade steady for me.


Photo of Paul Christenson

Paul Christenson

  • 6,174 Points 5k badge 2x thumb
You may need to use BOTH stabilizers when trying to loosen the blade

NOTICE: If the bolt rotates with the motor shaft when loosening the bolt, turn the fan by hand to align the through holes in the fan with the holes in the blade, and place another metal rod (e.g., a 3.5” length screw bit) with diameter less than 1/4 inch (6.35mm) into the aligned holes to act as another stabilizer (Fig. 23). (in your owner's manual)

5. Continue using the 9/16 inch (14mm) wrench to turn the blade bolt counterclockwise to loosen it completely.


Final Note: Just make sure you are turning the bolt COUNTERclockwise





(Edited)
Photo of NYWest

NYWest

  • 110 Points 100 badge 2x thumb
Thank you for the input. I am going to try a longer handled wrench to see if I can apply more force. 
Photo of Rick F

Rick F

  • 1,010 Points 1k badge 2x thumb
I put a screw driver in a hole near the blade to keep blade from fighting you.  Maybe this video will help: https://www.youtube.com/watch?v=WsZ272F001M

Photo of Michael Willson

Michael Willson

  • 60 Points
newer models do not have holes to stabilize blade
(Edited)
Photo of Oregon Mike

Oregon Mike, Champion

  • 37,250 Points 20k badge 2x thumb
Michael, which models don't? I see the new double battery mower does. At least it's shown in the manual. 
My older 21" does and I can't imagine EGO changing that feature on newer 21" models. 
Photo of Jim Hippen

Jim Hippen

  • 384 Points 250 badge 2x thumb
I have had success with an impact driver.
Photo of Prairiedog

Prairiedog

  • 3,542 Points 3k badge 2x thumb
Umm, Probably Not approved operating procedure but it took us a couple whacks with a mallet on our wrench to break the friction holding the bolt. Don't know if his reasoning was correct, but learned that years ago from a mechanic who explained it takes a brief sharp force to undo bolts that had been powerdriven on. This was in explaining why, as a scrawny teen, I couldn't get the tire iron to work on my flat. I was trying to "turn" it. He of course was burly enough to just give it a firm, quick jerk, but he showed me how I, with one whack of the mallet, could take the wheelnuts off like gravy. Having never obtained anything resembling brawnitude, it has been a successful go to move ever since. :)
Photo of dhau001

dhau001

  • 1,908 Points 1k badge 2x thumb
Second the impact driver.  Makes quick work of the bolt, on and off.  Since its impact and not a drill, safety profile is much better because it won't spin the lawn mower blade, maybe a little on the initial impact.  Still, for safety sake, stick a wood in there.
Photo of Jack375

Jack375

  • 244 Points 100 badge 2x thumb
I agree with prairiedog. Stand up and use a brief sharp forceful shove. I also blocked the blade with a block of wood held against the installed blade. At first I thought i had stripped the bolt but I had just loosened it.